your current location：首页 > news>Tips for the Dark (2) Super frequency overclocking [GT6] Gregtech 6 (Gregtech 6) Minecraft Game

Tips for the Dark (2) Super frequency overclocking [GT6] Gregtech 6 (Gregtech 6) Minecraft Game

2024-12-09 18:29:10|Myriagame |source：minecraft skins

This tutorial is set by the author to use the CC By-NC-SA protocol.

All versions of this tutorial

Payment -Please see it

Overclocking this means to increase the operating frequency of the CPU to improve the working ability of the CPU.

However, it means that the steam engine is overloaded in GT6.

I am not the first person to quote this term, and it is estimated that it will not be the last.

This tutorial is suitable for small problems in the early stage and has a reference effect on the later period.

The following content, if the specific description is not added, is the situation encountered in the early stage of the game.

1. Introduction

Overclocking is a very important technique.It will help some unexpected minor situations after you know how to make up supercharging.

2. Principle explanation

The steam in GT6 is produced by a boiler

We all know that there is a dial in the boiler

The pointer does not generate steam when the left white area.(Before 50%)

When the pointer reaches the green area, it starts to stabilize the steam, that is, the rated power is reached.(Reach 50%)

When the pointer crosses the red area, the boiler will explode.(100%, the left edges of dark green, green, yellow, orange and red are 50%, 60%, 70%, 80%, and 90%)

The picture below shows the description of the dense bronze boiler, I will pick up the key explanation

The energy input and energy output information in the figure above refer to the power when the boiler pointer reaches 50%.

So the question is. What is the output status of the boiler when the pointer exceeds 50%?

I answered: It will exceed the rated power slightly.

This slightly exceeds the steam output of the boiler too much,

For example, let the bronze steam engine output 16ku/T.

But it will overcome the effect of calcification on the output power of the boiler.

In fact, in the early stage, due to the lack of distilled water, everyone generally used water, and in this case, it is impossible for boilers to reach the rated power in the figure, and it will be calcified with continuously adding water.

This will cause the output power of the boiler to get lower and lower until it cannot drive the steam engine and steam turbine.

In particular, the turbine is particularly sensitive to the input power. Once the steam is not enough, it will strike and make a strange noise. If the amount of steam is too much, it will strike and make a strange noise.(There are differences between the two sounds, please compare yourself. There will be changes after exceeding the green area.)

At this time, the effect of supercharging overclocking is reflected.

We can let the pointer of the boiler cross the 12 o'clock and keep pressing the boiler.After the degree of pressure is appropriate, the output can be performed, and the impact of calculation can be performed and the power is increased in a short period of time.

3. Raise a chestnut

In the early stage, you want to use a turbine engine to drive the centrifugal machine

You will face a very interesting problem. A single set of ordinary bronze burning room boiler turbine engines cannot drive centrifuge to work.

Theoretically, this configuration meets the minimum RU input requirements for centrifuge work.But because ordinary water is used, boiler will be calcified.Balchets will reduce the ability of boilers to output steam.There are less steam, and there are less RU output by the turbine.And even the reduction of a Ting Ding point will cause the output power of the turbine to reach less than 16, but the infinite is close to 16.Therefore, the centrifuge does not work at this time.

At this time, there is a simple way for you to choose -supercharged overclocking.

As long as the boiler cannot output the steam, so that the pointer can exceed 50%to prepare.

When it exceeds a certain range, when it does not exceed the light green part, then correct the turbine with a wrench.(50%-70%)

At this time, the boiler will be output overclocking, and it will overcome the weakening of calcification, and you can centrifug the ashes.

Sometimes the supercharged will pass, and the turbine will also make strange sounds and will not work.Please pay attention to the degree of supercharging, do not exceed the green area.

4. Expansion effect

We can use supercharged overclocking to speed up the power of the machine.

For example, do not add water to boil the boiler at the beginning. After a period of time, add water. At this time, the pointer will rotate sharply.We want to rotate more than 50%and cannot exceed the red area.Then wait for the pointer to return to 50%, add water.Let the boiler work overclocking.Until the water is added, the effect of weakening the pressure overclocking, allowing the boiler to run at the rated power.

advantage:

Overcoming the weakening of calcification, let the machine overclocking work in a short time, and speed up the production of certain materials

shortcoming:

You need to understand the principle, and you need to accumulate a certain experience

more news

MORE +