Method for Fuscharge [TR] Tech Reborn (Tech Reborn) Minecraft Game

2024-12-10 17:47:09|Myriagame |source：minecraft skins

This tutorial is set by the author to use the CC By-NC-SA protocol.

This tutorial uses science and technology revival version: 3.8.4+build.236, game version: 1.16.5

First of all, you need to prepare the required materials: 1 fusion control computer, several nuclear clustering coils (the number depends on the size you want to do), a number of hydrogen units (industrial centrifugal machine centrifugal units and 氚 units), at least at least1 superconducting cable (for output energy), 1 AESU (for the energy and input energy for receiving the output), several arbitrary guide cables (recommended glass fiber wires)

Note: AESU is not necessary. You can use MFSU and other instead, but the input and output speed will be slow.

The size of this tutorial is 7, and 16 nuclear clustering coils are used.

Place the polytable control computer, and the structure will be prompted to be incomplete, as shown in the figure below.Click H to display the projection of the required nuclear clustering coil in the world, and then place the nuclear clustering coil to the specified location.You can also hold the nuclear clustering coil, and then press the use key (generally right -click) to control the computer at the fusion control computer.

Then connect the circuit according to the figure below:

The ① in the figure is the power generation equipment (the figure is used in the quantum solar panel), which is used to charge the first -time fusion heap.Generally, if you do not make mistakes in the future, you only need to charge it once.

The output of the AESU in the figure does not connect the glass fiber wire, but is connected to the air (the direction of the output end of the AESU is not fixed, and it will be adjusted according to the situation). Below AESU is the superconducting cable.

Note: The upper and lower sides of the polytable control computer are output surface, but only when the response will be output, and energy needs to be accepted as soon as possible. Therefore, the use of superconducting cables, the input surface on the four sides of the southeast and northwest.

After connecting to power generation equipment, the fixture control computer is charged to the 40M energy required to start reaction, and then the circuit of the power generation equipment is disconnected.

If you plan to use multiple times and temporarily do not output energy, then use a wrench to remove the superconducting cable below AESU.This tutorial takes output as an example.

Note: Do not remove the energy cache of the superconducting cable when the energy cache is not completed. Disassembly will cause energy to disappear.

Then open the GUI of the polytable control computer and adjust the multiple to 1.74X (the energy will be reduced after the initial multiple reaction) into the 氘 unit and 氚 unit (synthetic 氦-3)Plasma 元 unit).Both formulas will generate energy of 33554432 (about 33m). After the energy of 58384711.68 (about 58m) by 1.74 times, the reaction process lasted 102.4 seconds.

Note: After putting in the corresponding unit, you will start the reaction process immediately, please be ready before putting it in.Both formulas will lose 1 empty unit (that is, 1 tin ingot).The continuous reaction intermediate process does not require the 40M energy required for the reaction, so it is recommended to react multiple times.

After completion, the corresponding product will appear in the middle of the computer GUI.At this time, the energy stored by the polytable control should be 0, and the superconducting cable above accepts all the energy, and then the energy will be input to AESU at a speed of 8192 E/T (the maximum speed of AESU). After waitingThere is about 58m energy. At this time, you can use a wrench to adjust the direction of AESU to other machines that need to be used, or fill the item.

Note: Don't let the total energy below 40m, otherwise you need to replenish energy next time.

When starting again, adjust the circuit of the output surface of the AESU to the connection fusion control computer, and transmit the required 40M energy back.Then adjust the output surface of AESU to the air.Open the GUI of the polymerization control computer, and put it in the required reaction again.

After making a plasma module unit, you can use the final generator of this module: plasma generator.

• 

  National Service DNF Dark Ni

• 

  The new screenshot of the be

• 

  The 15th anniversary wallpap

• 

  3DM Xuanyuan Sinicization Gr

• 

  French magazine is the first

• 

  The sneak game "Republic" wi