your current location：首页 > news>Magic Art 3 Process Five Rune Carving & Rune Forging [MA3/MNA] Magic Art 3: Mana and Artific MINECRAFT Game

Magic Art 3 Process Five Rune Carving & Rune Forging [MA3/MNA] Magic Art 3: Mana and Artific MINECRAFT Game

2024-12-10 17:49:01|Myriagame |source：minecraft skins

This tutorial is set by the author's setting without permission.

Foreword

Rune engraving and rune enchantment are the new content of Magic Art 3, which is closer to the original and reality in terms of gameplay.(The combination of magic art is quite closely combined with the original MC)

Rune engraving

Preparation

Rune engraving needs to use the rune engraving table, below is the interface of the rune engraving table

Rune artisans and rune craftsmen are placed in the red box

Rune model in the blue box

Put the engraving formula in the green frame (non -required)

Rune model

Put the unprocessed rune model into the rune forged furnace to furnace to get the rune model

Engraving formula

Place the runes corresponding to the engraving formula to be made on the rune anvil, then place a piece of paper, then right -click the runes of the runes with charcoal or coal to get the corresponding rune engraving formula

(The runes are used here: qi)

In fact, compared to the engraving formula, there is a better way: open the corresponding entry of the mysterious ancient books, and click the button in the red circle in the upper left corner.

This page on the book will be displayed on the left side of the screen. When the carving is carved, it can also be used as a reference

Carving

The blank rune prototype is a 9 × 9 dot matrix. When the carving is carved, the left button can also engrave the next traces on the rune model between the two points.

Connect a trace of traces into what you want to make, the blank rune model will automatically become the corresponding rune model

When carving, please be careful. Once you are carved wrong, you can only discard this rune model and change a new one for re -carving

Rune forging

First of all, you need to make a piece of ultra -hot Worming ingot, and put the Wiming ingot in the rune forging furnace to be fired to get it.

Place the carved rune model on the rune anvil, and then place a piece of ultra -hot temperature ingot. The bottom of the rune iron anvil will appear as shown in the figure.

Right -click the runes of the rune artisan hammer. Click the runes anvil. The ultra -hot Wincterm ingot will be embedded in the rune model.

After ten times, the ultra -heat Wincter ingot will be converted into runes, and the aura at the bottom of the rune anvil will also disappear.

The karate right -click rune anvil can win the runes, and the right -click again to win the rune model

Note: Rune model has durability. Each rune model can be used four times. There is no way to take rune model durability.

It may be interesting to try rune forging for the first time, but there is a lot of runes in the middle and late stages of Magic Art 3, and the carving needs to be careful not to be wrong.

A large number of carvings and rune forging will still make people feel cumbersome. You can choose to use the installation automation carving and forging. The specific method will be introduced in detail in Chapter 6

Rune enchant

The rune iron anvil can also be used to enchant the equipment.

First make a rune with a curse

Then place the equipment to be enchanting and then the rune anvil, and then place a rune with a curse

If the rune iron anvil supports the curse corresponding to the equipment enchanting, blue aura will appear at the bottom of the rune anvil,

Right -click ten times using rune craftsman hammer. The enchantment rune will be embedded in the equipment, and the equipment will also get the enchanting effect of the runes

Change the enchantment runes with enchanting books, which can also have the same effect, so that compared with the use of the original iron anvil, it can save experience

However, the rune iron anvil cannot be used as an upgrade of the enchanting effect. Whether it is the enchantment (rune) of the two (one) quickly loaded the enchantment book (rune) into a (one) fast loading II enchantment book (rune),

It is not possible to knock on the magic book (rune) of the fast loading III (rune) to the crossbow with fast loading i or ii.

more news

MORE +
Hot news MORE +
Minecraft Skins MORE +