your current location：首页 > news>GTNH installation wiring automation optimization plan [GTNH] Gray Technology: New Vision (GT: New Horizons) Minecraft Ga

GTNH installation wiring automation optimization plan [GTNH] Gray Technology: New Vision (GT: New Horizons) Minecraft Ga

2024-12-10 17:51:32|Myriagame |source：minecraft skins

This tutorial is set by the author's setting without permission.

Introduction and resource

Characteristics of this design

{{

1. Do not use SFM, because SFM will conduct a lot of detection at all times, and it is necessary to detect a large number of assembly lines, and for some reason, it seems to cause a lot of stutter.At the same time, the SFM adds synthetic forms, and individuals never think it is convenient.*If this one is not true for you, then you must consider it.

2. Correspondingly, this device only causes a relatively large stuck when the assembly line is run (mainly source: box update)

3. Add the synthetic table to only add: packaging template, loading template, one each, then all the assembly lines can be fully operated.For some materials> 16SLOT requires two packaging templates.However, the published map is not supported, please see the instructions in this post.

4. The difficulty of reciprocating is medium.

5. Stability.*However, the synthetic formula of the circuit assembly cable will stop the assembly line inexplicably, and then use a soft hammer to start the material to disappear, and the finished product is not found (?

6. Heights are divided.

7. The packing machine can run faster and faster.

8. The assembly line material will prepare the post -formula material when synthetic the first formula.

}

Therefore, I think this is a [optimization plan]

Video display: https://www.bilibili.com/video/bv1av411n7me

Map download: link: https://pan.baidu.com/s/1_xo95WF2R03DCQ600pw extract code: TJ4P

Plan and logic

Average

It seems inconvenient to divide the items one by one.But it is convenient to be divided into one item.So use the packing machine.The relevant content has not yet been completed.So what is the packing machine here:

The packaging machine is an idea, that is, the actual packaging of multiple items is actually packed into one item, rather than the pseudo -pseudo -combined with one mark with one mark with one tag in the template.

It can be used to complete: multi -raw material distribution and average material.

One item of handbags can be decompressed into multiple.But it cannot automatically import and export.

If you replace it with a storage element, you can automatically import and export with the ME-IO port.But the items are chaotic.You can complete the TC injection/DE2 aggregate multi -raw material/average material to at most multi -block structure automation.

But for the assembly line, the white list is very troublesome.Therefore, using a compressed box (submarine box) to ensure the order of the items.

Put all the items (including the fluid unit/capacity bottle) in the compressed box, and then knock out the compressed box and put it back to the network.

The compressed box does not participate in the template.Automatically place (the right side)

The interface in the middle opens the blocking mode to place the material in the compressed box.

When the compressed box has items, it is destroyed and returns to the main network (detected above, destroy the left side)

16+ raw materials?

It is the classic multi -raw material distribution.But here is 16+ instead of 9+ because of the extensive model terminal of the teacher.If you want to use other integrated packages, you can also use the solution here.After the first packing, we need to pack the second time.

Logic as follows: Equipment: boxes, materials, place occupies.Block mode.

Enter the bus with a forming panel and place the compressed box (non -empty), and then put the material.

At this time, there is only one place occupying in the left side of the (compressed) box on the left. The number of items was detected <2, and then the placed compressed box was destroyed.

0 items were detected in the storage bus of the compressed box and took away the placeholder.

The box is uniformly distributed part

There are single items containers, so even EIO is not needed, but it can be used for use. Here is AE2.

Drama diagram:

Actual chart:

The composition is received at the magic base.

When the input bus of the assembly line is empty and the input bus 0.7s, the compressed box is placed when the input bus 0.7s.

Then draw the items to the assembly line.(Storage bus priority level)

Use a fuzzy white list to separate the capacity bottle out for fluid operations.The map provides a solution to the fluid to export the fluid, and it also makes a fluid import component scheme. However, it seems that the capacity of the import scheme is too small to use it at all.

The items are completed, the fluid is completed, and the assembly is started.

At this time, the item disappears: destroy the compressed box within 0.6s, and then 0.1s allows the next box to be pumped into the next box to prepare the next raw material. Whether the finished product has output has no direct restriction on the material network.Finally, keep the finished product, empty capacity bottle, and empty compressed box.other?

If you have the same dissatisfaction group items, do not stack it, please use renames.

And if the fluid packaging machine needs to be used ... it can be equivalent to the fluid (model) fluid to the quantum cylinder with 16*8B*15, pump into the fluid element of the drive, and then the number of items on the port (only read/only write, see for details, see for detailMap) from 0 to 1, remove a fluid element.End with fluid components, and the cycle is completed.

There is nothing else.

more news

MORE +
Hot news MORE +
Minecraft Skins MORE +