your current location：首页 > news>With thermal expansion, the steam turbine is permanently immersed.

With thermal expansion, the steam turbine is permanently immersed.

2024-12-10 17:52:18|Myriagame |source：minecraft skins

This tutorial is set by the author's setting without permission.

The steam turbine with AC generator must be the only choice for the energy supply in the previous and middle period.), Finding more efficient and cheap steam production methods is the core content of this tutorial.

Key module: heat expansion 5 (TE)

Optionable module: General Machinery, Pressure Pipeline

TE infinite production of steam originally explained that steam mainly relies on the production of "steam boiler conversion" upgraded thermal energy furnace production, while thermal energy furnace needs continuous supply of magma supply, and magma can be obtained by melting various stones through the lava furnace, and the stone can be obtained, and the stone canIt can also be produced by the unlimited stone manufacturer, which has formed an automated closed loop.

Specific operation:

The first is the supply of water sources.Here I use the unlimited water source block of the pressure pipeline and the mechanical pipeline of general machinery to extract water, and use the adjuster to configure the bottom -end mode of the mechanical pipeline connecting the unlimited water source block to draw, and then connect to the stonemaker.

It should be noted that when the water is entered into a stone machine from the side, the stone manufacturing machine will not take the initiative to receive it. You need to right -click the machine to adjust the configuration of the stonemaker. As shown in the figure::: Figure:

Since I am input from the left side, the corresponding position of the left side of the stone manufacturer can be pressed into a small black square. The black square represents the active extraction from this surface.The configuration is the same.The orange surface represents the output surface, and the product will output from this surface.

Then pour a bucket of magma into the stone machine, and you can start making stones (this process is no longer consumed, but magma is necessary)

Note: If you have the conditions to upgrade the "fire into the injection" suitable for the stone -making machine, the stone manufacturing machine will no longer consume the water source, which means that you don't need to supply water to the stonemaker.In addition, if the TE machine needs to be installed with an additional upgrade component, it will be upgraded at least to hardening levels, or changes in the configuration file, and the specific method will not be explained.

Next, the level of the lava furnace, the level of the lava furnace is at least hardening. In order to install and upgrade the "heat convection cycle", it is not enough, but the speed of burning stones is very slow.

It should be noted here that the lava furnace that is installed with a flow cycle will increase power consumption. It is not recommended to use it in the early stage!

Then make the same stone machine and adjust the configuration of the lava furnace to this. This is because my lava furnace and stone machine maker are close to one piece.Essence

Even if the heat circulation is installed, the efficiency of the lava furnace is relatively low, so you can upgrade the "auxiliary receiving coil" to increase the speed, but the power consumption will increase.The stone manufacturer is relatively fast, and there is no need to add an additional speed to upgrade.

The groove in the figure below is because I have changed the configuration file so much.The default is that there are 1 slot level in the hardening level. There are 2 grooves in the enhanced level, 3 fabrications, and 4 resonance.In fact, it is enough to upgrade to the enhancement level. The stone manufacturing machine itself is very fast, and the speed of energy furnace consumes magma is not so exaggerated.

Then place the thermal energy furnace next to the lava furnace, and then install the "steam boiler conversion" to the thermal energy furnace to transform the magma into a large amount of steam.

Although this stuff is written in the remarks of the steam boiler conversion, it is used for steam energy furnaces, and it can actually be used on thermal energy furnace. It is probably wrong.

Note: The slot position on the left side of the thermal energy furnace requires water supply, and the surface of the water supply is available in four sides.There are a variety of methods of water supply, so I won't go into details here. You can refer to the method of supplying water for stone manufacturers above. At present, no professional upgrade can prevent the water consumption of thermal energy furnace.

After all preparations are ready, the pipeline is connected from the top of the thermal energy furnace. The top is the active output surface of the thermal energy furnace. You can actively output the product steam, and then receive the steam turbine to solve the steam problem.The steam turbine does not connect to an external AC generator, which is not caused by work)

more news

MORE +
Hot news MORE +
Minecraft Skins MORE +