your current location：首页 > news>Boeing 737-300Classic passenger aircraft driving guide [Gap] Golden Airport Pack Minecraft Game

Boeing 737-300Classic passenger aircraft driving guide [Gap] Golden Airport Pack Minecraft Game

2024-12-10 17:52:54|Myriagame |source：minecraft skins

This tutorial is set by the author's setting without permission.

Check before taxi:

Open the control panel (keyboard U)

Open the engine oil pump (start the magnetic motor) (click on all the mags on the panel to make it all on the upper side)

Starting engine (long press the panel on its bright green indicator)

Open the total power supply (in reality is the navigation system) (click on the panel to be on the upper side)

Open the instrument lighting (Cabin on the panel)

Open the anti -collision light (Strobe on the panel)

Turn on the sliding light (taxi on the panel)

Turn off the panel (on the keyboard U)

Keeping the brakes and closing status (Y+B on the keyboard (the micro gas gate is tested, if the aircraft moves, it is a closed position.

Clear the throttle and stop (long press the keyboard on the keyboard for 10 seconds and long the keyboard on the keyboard until the plane stops completely)

Check before taking off:

Met the midline of the runway (if there is no runway, please ignore it)

Open the landing light (LAND on the panel)

Put the flap to 15 degrees (press the keyboard U to close the control panel, then press the keyboard H twice)

Check the wings 15 degrees

Check whether the total power supply and instrument lights are turned on (the NAV indicator on the panel is bright and green, located on the upper side, Cabin "1" side press)

Check whether the landing gear is released (the indicator light corresponding to the Gear on the panel is bright and green.

Check whether the anti -collision lights, sliding lights, and landing lights are turned on (all located on the upper side)

Check whether both of the engines on both sides have been activated (click on the all MAG lever on the control panel to make it located on the upper side. If so, please ignore it)

Check whether the REV is opened (the REV control lever on the panel is located on the upper side, if not, please click it)

Check whether the autonomous driving is closed (AUTO bright red indicator light on the panel)

Check the flat line (please install the flat watch for inspection, and turn the flat wheel (... trim) on the panel to make all the pointers on the flat table point to the middle position (one of which is parallel))

Check the checklist:

The throttle To/GA (takes off/resumption of flight) (long press the keyboard i until confirming the maximum thrust)

V1 (V1) (there is no accurate unit in the game, as long as you open the back -to -full speed, you can stop, so 70 units are temporarily set up)

VR (VR) (there is no accurate unit in the game, so 100 units are temporarily set up)

Lift the wheel (lift the wheel) (short press S)

Keep a suitable rising angle (25 degrees) (press on the keyboard W to lower the head of the machine)

Leaving the ground (departure) (height is rising)

Appropriate speed (suitable: 100)

Positive increase rate (positive increase rate)

Wicing wheel (click Gear's handle on the panel to make it located on the upper side and make the corresponding indicator light red) (yellow means being put away/put down)

Patrol inspection form:

The wing wings (short press multiple times on the keyboard y until the flap is completely put away)

Turn off the sliding light and landing lights (click on the panel TAXI and the corresponding lever corresponding to LAND to make it all in the lower side)

Waiting for the plane to climb to the required height

Flating (pressing on the keyboard until the plane is on the flat flight (here is defined as the height almost unchanged or slightly rising) state (the operation of the lower aircraft under the state of the throttle may be very difficult. If this is the case, it is recommended to collect the throttle in advance.At the same time, it is not advisable to collect more, otherwise it is easy to lose speed)

The accelerator (long press the keyboard until the throttle is in the right position) (If the above step has been completed, please ignore it)

Open the autonomous driving (click the button corresponding to Auto on the panel to keep it bright and green)

Notice during cruise:

Observe the speed at all times to prevent too fast or too slow (it is recommended to maintain 80 units, and the actual use can be adjusted by itself) (when the speed is too fast, you can press B to increase the spoiler on the keyboard to increase the speed to reduce the speed) (about 50 units around 50 units)Will be stunned, you can recover by increasing the throttle)

Checking form before falling:

Autonomous driving disconnection (click the button corresponding to Auto on the panel to keep it bright red)

Check the speed (70 to 80 units, please press B on the keyboard to decelerate, please be a micro gas gate)

5 degrees of flap (press H on the keyboard H)

Low down the machine and keep the maximum attack angle of -3 degrees (press W on the keyboard to lower the machine, you can adjust according to the actual situation)

Open the landing light (click the lever corresponding to the LAND on the panel to make it on the upper side)

Lowing checklist:

Met the midline of the runway (if there is no runway, please ignore it)

Based on the distance from the runway, put down the appropriate gear wings (a total of four gear) (the current distance four -class division, each equal time, put down the wing, keep the flap full at the last time)

Putting the wheel (about three gears in about three gears, click the Gear bypass handle on the panel to make it located on the lower side and let the corresponding indicator light bright green)

Control the throttle (control according to your own situation, the optimal units of 70-80 during grounding)

Pingping when grounding (when the throttle is gone when the runway is visually, it is recommended to ground at a 0 degree angle)

Specify (press the REV control lever on the panel after confirming the ground to make it located on the lower side, and at the same time, the microccuporcular gates are pushed to reverse) (B uses B on the keyboard to start with the motor wheel brakes and spoiler as the main deceleration method)

After the aircraft speed is lower than 20 units, turn off the reverse push, and make the throttle rod at idle level (click the REV control lever on the panel again to make it on the upper side) (long press on the keyboard to make the engine in the idle state)

Setting checklist:

如您建设了完全的航空港设施（包括必须的跑道以及附属的滑行道、停机位等），并且因此需要离开跑道时，请不要在减速时让飞机完全停下，并且微加油门（键盘上I) To make the plane have enough motivation to start gliding, at the same time turn off the landing light and turn on the sliding light (click the lever corresponding to the LAND on the panel to make it located on the lower side to turn off the landing light.Located on the upper side to turn on the sliding light)

Keep the speed below 10 units to safe taxi (can be adjusted according to the actual situation of the individual)

Turn off the runway at the right time and start gliding on the runway (press J on the keyboard to turn left to the left, and press L to turn right to the right./Side)

Specify to 5 units when the parking position midline or is about to reach the shutdown point (B on the keyboard B to decelerate)

Fully decelerate when you arrive at the shutdown point (long press on the keyboard B to completely decelerate)

Deployment is a brake (Y+B on the keyboard (press B when holding Y))

Check the checklist before the machine:

Turn off the engine (the lever corresponding to all the MAG on the panel makes it in the lower side)

Check the brakes to be connected to the state (the indicator lights corresponding to the brake control lever marked on the left side of the throttle rod are bright red)

Check the lighting of the lighting (NAV, Strobe, TAXI, LAND, Cabin lever or buttons on the panel are all in the lower side)

Leave (TAB on the keyboard)

Before you continue ...

more news

MORE +