your current location：首页 > news>A new idea of automation (blood magic+AE) that gets rid of the redstone output of the altar [BM2] Blood Magic 2 (Blood

A new idea of automation (blood magic+AE) that gets rid of the redstone output of the altar [BM2] Blood Magic 2 (Blood

2024-12-10 17:55:29|Myriagame |source：minecraft skins

Why is there this tutorial

It is well known that the red stone lamp below the blood magic altar allows the altar to release a particularly long red stone pulse after a synthesis.When I tried to use this pulse automation altar, I found that this pulse was a waste of time, so I tried not to use this pulse to automate blood magic.In fact, it is not very long, but if you do it, you have to find some excuses.

If you feel that there is a convenient control method, you don't need to be stupid (I also agree with partially), you can also look as a new automation idea.

Module and version requirements

MC version 1.12.2, the module has AE (the version of AE2 University Extended Life is used in this article, RS is probably okay, please try it by yourself) and blood magic. No other pipes are used in the automation process, but other pipes are used in the automation process, but other pipelines are used in blood input blood.Pipe module.

text

As shown in the figure, this is a blood magic level 5 altar with metastasis runes (increase blood input upper limit to prevent blood), promote runes (reduce blood transmission delay to prevent blood) and speed runes (accelerate accelerationSynthetic), the blood input uses MEK's catheter that creates fluid storage tanks and EIO. For actual situations, please solve the problem of blood input.

This method needs to be used for AE subnet, as shown below:

Among them, light blue is your main AE main network, and red is the subnet used by automation. It should be noted that the subnet cannot be used for storage.

Use a wrench to point the interface of the main network to the subnet interface, and the model to be automated in the main network interface.

(There are many ways to have a model position because the unofficial version adds the model card to expand the model position, and you can go to the unofficial page to view it.)

Storage bus directly under the altar, so that when the main network is distributed to the subnet, because the subnet does not have other places to store items, it will be directly put into the altar.

So how to control the output?

We know that putting a synthetic card in the sender and filtering can make the sender send a redstone signal when synthesizing the item.

So we made such a structure that used the output bus that labeled the blank slate to output the items on the subnet back to the main network. The output bus needs to be put in the redstone card and adjust the redstone mode to "active when there is a signal."

Put a square in front of the sender to turn the strong signal output by the sender into a weak signal to prevent the output bus next to the activation.

It's over!Copy and paste.When synthetic level 2 slate (enhanced slate), the output of only level 2 stones will be activated. At this time, only level 2 slate can be output to the Lord from the altar (connected to the storage bus connected to the subnet) to the LordThe network completes synthesis, and as a grade 1 slate (blank slate) as a material will be synthesized in the altar and then output.

Advantage and disadvantage

Because it is the idea of getting hot in my mind, in fact, I didn't save much time when I thought about it carefully. It also made each synthesis require an output bus. It can only be said that it is useful but useless.If you want to say an advantage, you can complete automation (not blood transfusion) in one side of the altar, and the part of the sub -network can also be placed elsewhere without squeezing near the altar.

However, there is another important issue in this idea!That is, it is quite unstable.Sometimes this method is feasible, but sometimes AE will be stumped. When there is no redstone signal input, it is still the product of the previous stage when entering the next synthetic stage, resulting in the input materials that are immediately pulled back.The reason why the problem is not clear for the time being. The temporary solution is not to be coded step by step, but to choose to input the coding of slate at all levels.If someone has the help of a idle worker on the help of the Fabric terminal Carpet module, what is the situation when the redstone signal of the previous stage is completed in the next stage of the synthesis of the previous stage.EssenceIn short, it is a rough and feasible method. As a new idea to get rid of the redstone signal output of the altar, it will be shared with you.

more news

MORE +