Remotely transmission of remote versions of magic/items [BOT] Botania Minecraft Game

2024-12-08 00:57:27|Myriagame |source：minecraft skins

This tutorial is set by the author to use the CC By-NC-SA protocol.

This tutorial is the specific implementation and improvement of another tutorial in the site. The text is connected below.

First, please see the simple demonstration video: BV1DU4Y1E798

This device is divided into two parts of the sending and receiving end, both of which are composed of two modules, including the same module 1, as shown below:

Function: Digging the target block and re -placing.

Replenish:

Magic launcher (Pulse Mana Spreader) Install Magic Mirror: Mana Lens: Messenger)

Mana Prism (Mana Prism) Install magic lens: MANA LENS: BORE and Magic lens: composite lens composed of mana lens: warp.

The pouring T wall around the transmitter must be placed, otherwise it is easy to cause the excavated block to fly out of the Rannuncarpus.

Module 2, as shown below:

Basic part:

Function: Output the magic slate (Mana Tablet) in Shulker Box, output the magic medium of magic slate to the MANA POOL to fill/release the magic power to the subtes, and finally send out a beam of magic to the other end.The module 1 lets it dig away the subclass and placed it on the Block of Manteel in the picture.

Replenish:

The transmitted lens and composite lens composed of transmitted lenses and messenger lenses under the force transmitter.

Another transmitter Install magic lens: Mana Lens: Boundce, which is set to the square under the palm flower.

The square under the palm of the module must be a block that can be charged by redstone.

The cells of the detector (Observer) on the movement path of the magic diamond (Block of Mana Diamond) must be a block that cannot be charged by redstone.

The Hovering Hourglass at the sending end is filled with a slate 6s with 6s in the case of three Manatic Bellows. At the receiving end, the magical slate is 25S.

Next is the different accessories on the two ports on the module 2 (the demonstration video is not installed, it is actually too lazy to record the video):

Send end:

Function: Magic detector.When the magic is sufficient/insufficient, a beam of magic signal is sent to the receiving end accessory.

Replenish:

The transmitter is installed with a composite lens composed of transmitted lens and messenger lenses.

The spark of the magic pond of the launcher is upgraded to a spark upgrade: Spark Augment: Recessive.

The magic pool of Spark and Module 2 and other magic ponds to be transported.

Another detected magic pool should be kept away from the magic pond in the module 2 as much as possible.

Receiving end:

Function: Control the signal emitter after the receiving end is ended. If the magic is insufficient, it will prevent this magic launch. Waiting for the sending end magic to unlock and activate the magic transmitter.

Supplement: The block where the red stone fire handle and the recreigator are charged must be a block that can be charged.

Then assemble the corresponding modules to be used normally.

As for the transportation items, the module 1 is retained, and the 2 part of each end module is changed to the following:

Send end:

Receiving end:

Supplementary: Red Stringed Container number is free to choose from, which can be superimposed.

Finally attached the archive link, version: 1.16.5-419.

For the first time to write a tutorial, please contain and correct any wrong places, and thank you

Recently, I have made a small modification, and the overall thinking has not changed.The specifics are as follows:

change:

A group of new red line containers shorten the time required for the empty subcarcule box.

Newly increased 4 times the magic interaction, so that the double -end hourglass only needs 7s to fully release/fill the energy magic slate.

Mark the funnel flower to prevent suction.

Add a small weak magnetic orchid (near the 4 magic pond), in addition to responding to magnetic rings and card positions.

Optimized the overall line and let ordinary pistons be activated once.

After the change, the corresponding detection device can be run normally for the double -end installation:

On the left is the sender, receiving on the right

New link: https://wwcy.lanzouq.com/iln2e1eczuzi

• 

  National Service DNF Dark Ni

• 

  The new screenshot of the be

• 

  The 15th anniversary wallpap

• 

  3DM Xuanyuan Sinicization Gr

• 

  French magazine is the first

• 

  The sneak game "Republic" wi